| |
Operation Instructions for the
Fast Draw Speed-Timer 3000
Install a 9 volt Alkaline Battery in the battery compartment of the Fast Draw Speed-Timer 3000, plug in the RJ9 Jack on the end of the 25 Foot cable (included) into the socket on the timer unit and position the light package up to 25 feet away (behind plexiglass in wax target or in the light position of a balloon target).
- Practice Mode with Ready Lights and Random Start:
Press and hold down the START/RESET key on the Fast Draw Speed-Timer 3000 from one to three seconds ("3 sec" will appear on the screen), release the START/RESET key to initiate the record mode with a Practice Mode start. This mode includes:
- A delay of approximately 2 seconds after releasing the button to allow you to position your hands at the gun.
- The light will then flash three times for a total of 2 seconds to simulate the "Shooter on the Line, Shooter Set" command.
- The light will then go out, followed by a 2-5 second random delay before the light comes on solid for 2 seconds.
Draw and fire when the light comes on. The timer display will indicate the number of shots fired, the total elapsed time for all shots, and the split time between the last two shots if more than one shot is fired (the cross-over time in Doubles).
- Timer Operator Mode with Random Start:
Press and hold down the START/RESET key on the Fast Draw Speed-Timer 300 for at least three seconds ("0 sec" will appear on the screen), give the "Shooter on the Line, Shooter Set" command, then release the START/RESET key to initiate the random delay mode. There will be a 2-5 second random delay before the light comes on solid for 2 seconds. Draw and fire when the light comes on. The timer display will indicate the number of shots fired, the total elapsed time for all shots, and the split time between the last two shots if more than one shot is fired (the cross-over time in Doubles).
- Timer Operator Mode with Instant Start:
Press and hold down the MODE key on the Fast Draw Speed-Timer 3000 for this entire sequence, then press the START/RESET key for three seconds ("0 sec" will appear on the screen). While continuing to press the MODE key release the START/RESET key to initiate the Record Mode and turn on the target light for 2 seconds. Draw and fire when the light comes on. The timer display will indicate the number of shots fired, the total elapsed time for all shots, and the split time between the last two shots if more than one shot is fired (the cross-over time in Doubles).
- Review Mode:
To review all shots fired (in order) within one minute of activation of the Record Mode, press and release (less than one second) the START/RESET key cycling through the shots fired. Press and release START/RESET key (less than one second) for all remaining shots.
- On/Off
The display on the timer will automatically shut off when not in use for more than one minute during the Record Mode or Review Mode, or while in the review you can press the MODE key to shut the timer off. You will not lose the shot times in memory. Press and release the START/RESET key at any time for less than one second to reactivate. The timer will turn itself off if no shots are recorded within one (1) minute in the Record Mode.
Instructions for the use of a Fast Draw Speed-Timer 3000 with a Remote Shot Display unit (purchased separately)
- Fast Draw Speed-Timer 3000 and Fast Draw Display
Turn on the Display with the on/off switch located on the left side of the unit. P7 will appear on the screen, indicating the Display is a Fast Draw Display, followed by the Display ID (E.G. 1234). It will then display 0.000 indicating that the Fast Draw Display is in the Ready Mode to receive times. Begin timing using the normal timer instructions listed above, and watch the Fast Draw Display unit display your times.
Note: you may have to set your timer and display to communicate using the instructions below.
- Setting your Fast Draw Speed-Timer 3000 to Communicate with a Fast Draw Display
Your Fast Draw Speed-Timer 3000 and Fast Draw Display has had the ID factory set, but any Fast Draw timer can be programmed to communicate with any Fast Draw Display using the following method:
Install a 9 volt Alkaline Battery in the battery compartment of the Fast Draw Display or plug the 9 Volt/110 Volt Adapter (included) into the adapter connector located on the bottom of the Fast Draw Display and then into a suitable 110 volt power source.
Turn on the Fast Draw Display with the on/off switch located on the left side of the unit. P7 will appear on the screen, indicating the Display is a Fast Draw Display, followed by the Displays ID (E.G. 1234) and then the Fast Draw Display will display 0.000 indicating that the Fast Draw Display is in the Ready Mode to receive times from the Fast Draw Speed Timer.
Make a note of the ID that was displayed, on the screen of the Fast Draw Display, which will appear for approximately 2 seconds as above.
Hold down the MODE key on the Fast Draw Speed Timer for 10 seconds. A four digit ID will be displayed on the Fast Draw timer with the first digit flashing. Using the up and down arrow keys set the first number if required to the first number that the Fast Draw Display displayed when it was first turned on and press the MODE key. The second digit will now be flashing, again using the arrow keys up or down to set this digit and press the MODE key. Repeat this process for all remaining digits and press the MODE key to finish. Your Fast Draw Speed-Timer 3000 is now preset to communicate with this Fast Draw Display only.
Note: This setting will not change unless you repeat the above process. Removing or changing the batteries or the power source does not effect these setting on either the Fast Draw Speed Timer or the Fast Draw Display.
Check the Fast Draw picture page for more details and photos of the timer and display in use.
You can download a PDF version of the instructions sheets that are included with the Fast Draw timer.
Return to the Main Fast Draw timer page
|
|
|
